Considering subsonic incompressible airflow through a Venturi, which statement is correct? 1) The dynamic pressure in the throat is the same as in the undisturbed airflow. 2) The total pressure in the throat is higher than in the undisturbed airflow.
Câu 3
During the retraction of the flaps at a constant angle of attack the aeroplane starts to: (Note: all other factors of importance being constant)
Câu 4
The stall speed in a 60° banked turn increases by the following factor:
Câu 5
When an aeroplane enters ground effect:
Câu 6
If the aspect ratio of a wing increases whilst all other relevant factors remain constant, the critical angle of attack will:
Câu 7
Asymmetric propeller blade effect is mainly induced by:
Câu 8
Which of these statements about the gust load factor on an aeroplane are correct or incorrect? 1) When the wing area decreases, the gust load factor decreases. 2) When the EAS decreases, the gust load factor decreases.
Câu 9
Regarding the lift formula, if airspeed doubles, lift will:
Câu 10
In a steady, level, co-ordinated turn:
Câu 11
Which statement is correct? 1) Propeller gyroscopic effect occurs during flight at constant aeroplane attitude. 2) Propeller gyroscopic effect is most noticeable during low speed flight at low propeller RPM.
Câu 12
The point where a laminar boundary layer becomes turbulent is called:
Câu 13
The sonic boom of an aeroplane flying at supersonic speed is created by:
Câu 14
"Tuck under" is caused by _ (i) movement of the centre of pressure (CP) of the wing and _ (ii) change of the downwash angle at the location of the stabilizer.
Câu 15
Which of these statements about weight or mass is correct?
Câu 16
A laminar boundary layer is a layer, in which:
Câu 17
The centre of gravity moving aft will:
Câu 18
An aeroplane in straight and level flight at 100 kts is subjected to a sudden disturbance in speed. Assuming the angle of attack remains constant initially and the load factor reaches a value of 1.44:
Câu 19
Assuming zero wind, an aeroplane in a straight steady glide will achieve the minimum glide angle at:
Câu 20
Which of the following statements is correct? 1) When the critical engine fails during take-off the speed VMCL can be limiting. 2) The speed VMCL is always limited by maximum rudder deflection.
Câu 21
Considering subsonic incompressible airflow through a Venturi, which statement is correct? 1) The dynamic pressure in the throat is lower than in the undisturbed airflow.
Câu 22
The total pressure in the throat is lower than in the undisturbed airflow.
Câu 23
What is the approximate value of the lift of an aeroplane at a gross weight of 50 000 N, in a horizontal coordinated 45° banked turn?
Câu 24
Which statement about propeller icing is correct? 1) Propeller icing increases blade element drag and reduces blade element lift. 2) Propeller icing reduces propeller efficiency.
Câu 25
What happens if CG moves behind the aft limit?
Câu 26
One method to compensate adverse yaw is a:
Câu 27
If the maximum pull force acceptable is 50 lbs and the design limit load factor of the aircraft is 6g. what stick force/g must be achieved to permit the aircraft to be manoeuvred to its design load factor limit?
Câu 28
Which of these statements concerning propellers is correct?
Câu 29
Induced drag is the result of:
Câu 30
Which statement about propeller noise is correct? 1) Propeller noise decreases when the blade tip speed increases. 2) For a given engine and propeller blade shape, an increase in the number of propeller blades allows for a reduction in propeller noise.
Câu 31
With increasing altitude and constant IAS the static lateral stability (i) and the dynamic lateral/directional stability (ii) of an aeroplane with swept back wing will:
Câu 32
Which of these statements about wing sweepback are correct or incorrect? 1) Decreasing wing sweepback decreases MCRIT. 2) Decreasing wing sweepback increases the drag divergence Mach number.
Câu 33
The total drag of a three dimensional wing consists of:
Câu 34
In a steep turn to the left, when using flight spoilers for roll assistance and at the same time for reducing the airspeed:
Câu 35
In a single engine aircraft with a clockwise rotating propeller (seen from behind), a left yaw is generated due to:
Câu 36
In supersonic flight, all disturbances produced by an aeroplane are:
Câu 37
The resistance, or skin friction, due to the viscosity of the air as it passes along the surface of the wing is pan of the:
Câu 38
Which of these statements about induced drag are correct or incorrect? 1) Induced drag decreases as angle of attack increases. 2) At constant load factor, induced drag increases with increasing aeroplane mass.
Câu 39
Assuming no flow separation, which of these statements about the flow around an aerofoil as the angle of attack increases are correct or incorrect? 1) The stagnation point moves up. 2) The point of lowest static pressure moves forward.
Câu 40
With a L/D ratio of 9:1 and flying at 12000 ft the glide range in still air would be approximately:
Câu 41
Which statement, about the effects on drag of fitting external tip tanks to the wings of an aeroplane, is correct? 1) Parasite drag increases. 2) Induced drag decreases.
Câu 42
Which of these statements about the gust load factor on an aeroplane are correct or incorrect? 1) When the mass increases, the gust load factor decreases. 2) When the altitude decreases, the gust load factor decreases.
Câu 43
Which of these statements concerning flight in turbulence is correct?
Câu 44
Left rudder pedal input will cause a:
Câu 45
Which of these statements are correct or incorrect regarding a sideslip, with the relative airflow coming from the right, on an aeroplane that exhibits both directional and lateral stability? 1) The initial tendency of the nose of the aeroplane is to move to the right. 2) The initial tendency of the left wing is to move down.
Câu 46
For a fixed-pitch propeller in flight at a given TAS, the blade angle of attack will:
Câu 47
MMO can be exceeded in a climb at a constant IAS because:
Câu 48
What changes in aircraft control must be made to maintain altitude while the airspeed is being decreased?
Câu 49
Which statement, about an aeroplane leaving ground effect at constant angle of attack, is correct?
Câu 50
The lift coefficient CL increases.
Câu 51
The induced drag coefficient CDi decreases.
Câu 52
Which aeroplane behaviour will be corrected by a yaw damper?
Câu 53
Which of these statements about flutter are correct or incorrect? 1) Wing mounted engines extending ahead of the wing contribute to wing flutter suppression. 2) Excessive free play or backlash increases the speed at which control surface flutter occurs.
Câu 54
Assuming zero wind, an aeroplane with a L/D ratio of 25:1 would cover a distance of
Câu 55
Which statement about an aeroplane entering ground effect is correct? 1) The downwash angle remains constant. 2) The induced angle of attack decreases.
Câu 56
Ignoring downwash effects on the tailplane, extension of Fowler-type flaps, will produce:
Câu 57
When Fowler type trailing edge flaps are extended at a constant angle of attack, the following changes will occur:
Câu 58
Given: Aeroplane mass: 50 000 kg;Lift/Drag ratio: 12;Thrust per engine: 21 000 N;Assumed g: 10 m/s²; For a straight, steady, wings level climb of a four-engine aeroplane, the all engines climb gradient will be:
Câu 59
On an asymmetrical, single curve aerofoil, in subsonic airflow, at low angle of attack, when the angle of attack is increased, the centre of pressure will (assume a conventional transport aeroplane):
Câu 60
Which of these variables are required to calculate drag using the drag formula?
Câu 61
Assuming ISA conditions and no compressibility effects, if an aeroplane maintains straight and level flight at the same angle of attack at two different altitudes, the:
Câu 62
To hold a given sideslip angle and airspeed. increased geometric dihedral would:
Câu 63
A jet transport aeroplane is in a straight climb at a constant IAS and constant weight. The operational limit that may be exceeded is:
Câu 64
Which of these statements about an oblique shock wave are correct or incorrect? 1) The static temperature behind an oblique shock wave is lower than in front of it. 2) The static pressure behind an oblique shock wave is lower than in front of it.
Câu 65
The bow wave will first appear at:
Câu 66
In general jet transport aeroplanes with power assisted flight controls are fitted with an adjustable stabiliser instead of trim tabs on the elevator. This is because:
Câu 67
Which of these statements about flutter are correct or incorrect? 1) Aero-elastic coupling does not affect flutter characteristics. 2) Occurrence of flutter is independent of IAS.
Câu 68
Which of these statements about an oblique shock wave are correct or incorrect? 1) The Mach number behind an oblique shock wave is higher than in front of it. 2) The total pressure behind an oblique shock wave is lower than in front of it.
Câu 69
A forward CG shift
Câu 70
In twin engine aeroplanes with propellers turning clockwise as seen from behind:
Câu 71
Given: Aeroplane mass: 50 000 kg; Lift/Drag ratio: 12; Thrust per engine: 28 000 N; Assumedg: 10 m/s²; For a straight, steady, wings level climb of a three-engine aeroplane, the one-engineinoperative climb; gradient will be:
Câu 72
Directional stability is the stability around the:
Câu 73
The critical angle of attack for the flaps down configuration, compared to flaps up is:
Câu 74
When an aircraft is flying at speeds above Mach 1, pressure disturbances from the aircraft will affect only the flow:
Câu 75
Which of these statements about induced drag are correct or incorrect? 1) Induced drag increases as angle of attack decreases. 2) At constant load factor, induced drag increases with decreasing aeroplane mass.
Câu 76
The contribution of the wing to the static longitudinal stability of an aeroplane:
Câu 77
What is the most effective flap system?
Câu 78
Which of these statements about the gust load factor on an aeroplane are correct or incorrect? 1) When the wing area increases, the gust load factor decreases. 2) When the EAS increases, the gust load factor decreases.
Câu 79
The relationship between induced drag and the aspect ratio is:
Câu 80
Given an aeroplane with a propeller turning anti-clockwise as seen from behind, the torque effect will tend to:
Câu 81
Which statement, about an aeroplane entering ground effect at constant angle of attack, is correct? 1) The lift coefficient CL decreases. 2) The induced drag coefficient CDi increases.
Câu 82
Which of the following (i) aerofoils and (ii) angles of attack will produce the lowest MCRIT values?
Câu 83
Comparing the differences between a horizontal trimmable stabiliser and an elevator trim tab, which of these statements are correct or incorrect? 1) An elevator trim tab is more suitable to cope with the large trim changes generated by the high lift devices on most jet transport aeroplanes. 2) A trim tab runaway causes less control difficulty.
Câu 84
Speed brakes are devices used on large transport category aircraft:
Câu 85
Which statement about a propeller is correct? 1) Asymmetric blade effect increases when engine power is increased. 2) Asymmetric blade effect is independent of the angle between the propeller axis and the airflow through the propeller disc.
Câu 86
If the propeller pitch of a windmilling propeller is increased during a glide at constant IAS the propeller drag in the direction of flight will:
Câu 87
One advantage of a movable-stabiliser system compared with an elevator trim system is that:
Câu 88
Which statement about stick force per G is correct?
Câu 89
Dihedral of the wing is:
Câu 90
Considering subsonic incompressible airflow through a Venturi, which statement is correct? 1) The dynamic pressure in the throat is higher than in the undisturbed airflow.
Câu 91
The total pressure in the throat is lower than in the undisturbed airflow.
Câu 92
If TAS is kept constant, to maintain straight and level flight with reduced air density the angle of attack of an aircraft's wings must be:
Câu 93
An aeroplane is performing a co-ordinated level turn with a constant bank angle. If the airspeed is increased the rate of turn will _ (i) and the load factor will _ (ii)
Câu 94
How does positive camber of an aerofoil affect static longitudinal stability?
Câu 95
A statically stable aeroplane:
Câu 96
At MCRIT, a shockwave will appear first:
Câu 97
Which statement is correct? 1) The angle of attack of a positively cambered aerofoil has a negative value when the lift coefficient equals zero. 2) There is a nose down pitching moment about a positively cambered aerofoil when the lift coefficient equals zero.
Câu 98
Comparing the differences between a horizontal trimmable stabiliser and an elevator trim tab, which statement is correct? 1) A stabiliser trim is less suitable for jet transport aeroplanes because of their large speed range. 2) A trim tab is a more powerful means of trimming.
Câu 99
Considering subsonic incompressible airflow through a Venturi, which statement is
correct? 1) The dynamic pressure in the throat is lower than in the undisturbed airflow. 2) The total pressure in the throat is higher than in the undisturbed airflow.
Câu 100
Which of these statements about stall speed is correct?
Câu 101
Which of these statements about the gust load factor on an aeroplane are correct or
incorrect? 1) When the slope of the lift versus angle of attack curve decreases, the gust load factor increases. 2) When the wing loading decreases. the gust load factor increases.
Câu 102
A rectangular wing, compared to other wing planforms, has a tendency to stall:
Câu 103
During a short period oscillation, the altitude:
Câu 104
When the CG Is close to the forward limit:
Câu 105
Propeller slip is the difference between the:
Câu 106
The speed for minimum glide angle occurs at an angle of attack that corresponds to
(assume zero thrust):
Câu 107
Which of the following statements about a constant speed propeller is correct?
Câu 108
The lift coefficient CL versus angle of attack curve of a positively cambered aerofoil
section intersects the horizontal axis of the graph:
Câu 109
Which of the following statements concerning control is correct?
Câu 110
Propeller blade twist is the:
Câu 111
Which of these statements about the strength of wing tip vortices are correct or incorrect? 1) Assuming no flow separation, the strength of wing tip vortices increases as the angle of attack decreases. 2) The strength of wing tip vortices increases as the aspect ratio increases.
Câu 112
Which moments or motions interact in a Dutch roll?
Câu 113
The parameters that can be read from the "parabolic polar'' curve of an aeroplane are the:
Câu 114
One disadvantage of wing sweep back is:
Câu 115
An aeroplane has static directional stability if, when in a sideslip with the relative airflow coming from the left, initially the:
Câu 116
Considering subsonic incompressible airflow through a Venturi, which statement is
correct? 1) The dynamic pressure in the undisturbed airflow is lower than in the throat. 2) The total pressure in the undisturbed airflow is higher than in the throat.
Câu 117
An aeroplane flying at 200 kts in straight and level flight is subjected to a disturbance that suddenly decreases the speed by 80 kts. Assuming the angle of attack remains constant, the load factor will initially:
Câu 118
Which of these statements about wing sweepback are correct or incorrect? 1) Increasing wing sweepback increases MCRIT. 2) Increasing wing sweepback increases the drag divergence Mach number.
Câu 119
When flaps are deployed at constant angle of attack the lift coefficient will:
Câu 120
Which statement is correct about a spring tab?
Câu 121
During a climb at a constant IAS, the Mach number will:
Câu 122
As fuel is consumed during a level flight cruise at high level:
Câu 123
To cover the greatest distance when gliding, the gliding speed must be:
Câu 124
Which statement about an aeroplane entering ground effect is correct? 1) The downwash angle increases. 2) The induced angle of attack increases.
Câu 125
An in-flight move of the CG of an aircraft further aft will:
Câu 126
Assuming ISA conditions and a climb above the tropopause at constant Mach number and aeroplane mass, the:
Câu 127
The forces of lift and drag on an aerofoil are, respectively, normal and parallel to the:
Câu 128
A "slat" on a wing is:
Câu 129
The aerodynamic centre of a wing is the point relative to which:
Câu 130
The effect of Mach trim on stick forces for power operated controls:
Câu 131
Aileron reversal may be caused by:
Câu 132
At constant EAS, what is the effect on aerodynamic damping as height increases?
Câu 133
Considering subsonic incompressible airflow through a Venturi, which statement is
correct? 1) The dynamic pressure in the undisturbed airflow is lower than in the throat. 2) The total pressure in the undisturbed airflow and in the throat is the same.
Câu 134
VMCA is the minimum speed at which directional control can be maintained when,
Câu 135
Just above the critical Mach number the first evidence of a shock wave will appear at the:
Câu 136
Which statement is correct regarding the gyroscopic effect of a clockwise rotating
As angle of arrack is increased on a conventional low speed aerofoil at low subsonic
speeds, flow separation normally starts on the:
Câu 141
If angle of attack is increased beyond the critical angle of attack, the lift coefficient _ and the stagnation point moves _ .
Câu 142
Assuming standard atmospheric conditions, in order to generate the same amount of lift as altitude is increased, an aeroplane must be flown at:
Câu 143
The lift coefficient CL versus angle of attack curve of a negatively cambered aerofoil section intersects the vertical axis of the graph:
Câu 144
For a given elevator deflection, aeroplane longitudinal manoeuvrability decreases when:
Câu 145
Which of these statements about an oblique shock wave are correct or incorrect? 1) The Mach number behind an oblique shock wave is lower than in front of it. 2) The total pressure behind an oblique shock wave is lower than in front of it.
Considering subsonic incompressible airflow through a Venturi, which statement is
correct? 1) The static pressure in the throat is higher than in the undisturbed airflow. 2) The speed of the airflow in the throat is the same as in the undisturbed airflow.
Câu 149
Two identical aeroplanes A and B, with the same mass, are flying steady level coordinated 20° bank turns. If the TAS of A is 130 kts and the TAS of B is 200 kts:
Câu 150
Wing loading is the ratio of:
lift to wing weight
wing area to wing weight.
lift to aircraft weight
aircraft weight to wing area.
Câu 151
Considering subsonic incompressible airflow through a Venturi, which statement is
correct? 1) The static pressure in the throat is lower than in the undisturbed airflow. 2) The speed of the airflow in the throat is the same as in the undisturbed airflow.
Câu 152
What is the effect on an aeroplane's characteristics of extending Fowler flaps to their fully extended position?
Câu 153
Which of these statements about the supersonic speed range is correct?
Câu 154
Which statement is correct?
Câu 155
If the increased downwash at the tail plane due to lowering (extending) trailing edge flaps is considered in isolation:
Câu 156
Which statement is correct? 1) A stick pusher activates at a higher angle of attack than a stick shaker. 2) A stick pusher prevents the pilot from increasing the angle of attack further.
Câu 157
Which of the following statements about static lateral and directional stability is correct?
Câu 158
Which of the following wing planforms produces the lowest induced drag? (assume zero wing twist)
Câu 159
An engine failure can result in a windmilling (i) propeller and a non-rotating (ii) propeller. Which statement about propeller drag is correct?
Câu 160
What is the limit load factor of a large transport aeroplane?
Câu 161
Flutter sensitivity of an aeroplane wing is reduced by:
Câu 162
When comparing the properties of laminar and turbulent boundary layers, which of the following statements is correct?
Câu 163
Upon extension of a wing spoiler, if the angle of attack remains constant:
Câu 164
For a given aeroplane which two main variables determine the value of VMCG?
Câu 165
The total pressure: (note: rho = density)
Câu 166
Which part of the aeroplane has the largest effect on induced drag?
Câu 167
A transonic Mach number is a Mach number:
Câu 168
On an aircraft with an all -moving tail plane. backward movement of the control wheel in flight causes:
Câu 169
Which statement is correct about the gust load on an aeroplane (IAS and all other factors of importance remaining constant)? 1) When the mass decreases, the gust load factor increases. 2) When the altitude increases, the gust load factor increases.
Câu 170
Which of these statements about flutter are correct or incorrect? 1) Aero-elastic coupling does not affect flutter characteristics. 2) The risk of flutter increases as IAS increases.
Câu 171
The main purpose of a boundary-layer fence on a swept wing is to:
Câu 172
When the speed over an aerofoil section increases from subsonic to supersonic, its
aerodynamic centre:
Câu 173
Aileron flutter can be caused by:
Câu 174
If density is kept constant, the dynamic pressure:
Câu 175
Which of these statements about "tuck under" are correct or incorrect? 1) A contributing factor to "tuck under" is a forward movement of the centre of pressure of the wing. 2) A contributing factor to "tuck under" is a reduction in the downwash angle at the location of the horizontal stabilizer.
Câu 176
The stick force per g of a heavy transport aeroplane is 300 N/g. What stick force is required, if the aeroplane in clean configuration is pulled to the limit manoeuvring load factor from a trimmed horizontal straight and steady flight?
Câu 177
Compared to a straight wing of the same airfoil section a wing with a 30° sweep-back should theoretically have an MCRIT _ (i) times the MCRIT of the straight wing. However, in practice the swept wing will gain _ (ii) that increase.
Câu 178
A swept wing compared to the same wing without sweep will provide:
Câu 179
The axes of an aircraft by definition must all pass through the:
Câu 180
The lift coefficient CL versus angle of attack curve of a negatively cambered aerofoil section intersects the horizontal axis of the graph:
Câu 181
The lift coefficient (CL) of an aeroplane in steady horizontal flight is 0.42. An increase in angle of attack of 1 degree increases CL by 0.1. A vertical up gust instantly changes the angle of attack by 3°. The load factor will be:
Câu 182
A line connecting the leading and trailing edge midway between the upper and lower surface of an aerofoil. This definition is applicable for:
Câu 183
If the stall speed of an aeroplane is 60 kts, at what speed will the aeroplane stall if the load factor is 2?
Câu 184
Which is one of the disadvantages of excessive increasing of the number of propeller blades (beyond a certain number)?
Câu 185
Assuming no flow separation, which of these statements about the flow around an aerofoil as the angle of attack decreases are correct or incorrect? 1) The stagnation point moves down. 2) The point of lowest static pressure moves aft.
Câu 186
An aeroplane is performing a co-ordinated level turn with a constant 30° bank angle. If the airspeed is increased the rate of turn will _ (i) and the radius of turn will _ (ii).
Câu 187
The manoeuvrability of an aeroplane is best when the:
Câu 188
An increase in geometric dihedral in a steady sideslip condition at constant speed would:
Câu 189
The regime of flight from the critical Mach number up to approximately M = 1.3 is called the:
Câu 190
Which of these statements about a trimmable horizontal stabilizer is correct?
Câu 191
As the centre of gravity is changed, recovery from a stall becomes progressively:
Câu 192
The point, where the aerodynamic lift acts on a wing is:
Câu 193
An aeroplane flying at 200 kts in straight and level flight is subjected to a disturbance that suddenly decreases the speed by 40 kt. Assuming the angle of attack remains constant, the load factor will initially:
Câu 194
Which of these statements about the gust load factor on an aeroplane are correct or incorrect? 1) When the mass increases, the gust load factor increases. 2) When the altitude increases, the gust load factor increases.
Câu 195
When the blades of a propeller are in the feathered position:
Câu 196
In order to fly a rate one turn at a higher airspeed, the bank angle must be:
Câu 197
Which statement is correct regarding the gyroscopic effect of a clockwise rotating
Câu 198
The application of the area rule on aeroplane design will decrease the:
Câu 199
Assuming no compressibility effects, induced drag at constant IAS is affected by:
Câu 200
What is the highest speed possible without supersonic flow over the wing?
Câu 201
Increasing the number of propeller blades will:
Câu 202
Assuming ISA conditions and a descent above the tropopause at constant Mach number and aeroplane mass, the:
Câu 203
Comparing the differences between a horizontal trimmable stabiliser and an elevator trim tab, which of these statements are correct or incorrect? 1) A stabiliser trim is more suitable to cope with the large trim changes generated by the high lift devices on most jet transport aeroplanes. 2) A stabiliser trim runaway causes less control difficulty.
Câu 204
Considering subsonic incompressible airflow through a Venturi, which statement is
correct? 1) The dynamic pressure in the undisturbed airflow is higher than in the throat. 2) The total pressure in the undisturbed airflow is higher than in the throat.
Câu 205
The function of the stick pusher is:
Câu 206
Which statement. about an aeroplane leaving ground effect at constant angle of attack, is correct? 1) The lift coefficient CL decreases. 2) The induced drag coefficient CDi remains constant.
Câu 207
Mach buffet occurs:
Câu 208
A jet aeroplane equipped with inboard and outboard ailerons as well as spoilers is cruising at its normal cruise Mach number. In this case:
Câu 209
Considering subsonic incompressible airflow through a Venturi, which statement is correct? 1) The static pressure in the undisturbed airflow is the same as in the throat. 2) The speed in the undisturbed airflow is lower than in the throat.
Câu 210
Which statement about a propeller is correct? 1) Asymmetric blade effect increases when engine power is increased. 2) Asymmetric blade effect reduces when the angle between the propeller axis and the airflow through the propeller disc increases.
Câu 211
Given: theta = pitch angle; gamma = flight path angle; alpha = angle of attack; no wind, bank or sideslip. The relationship between these three parameters is:
Câu 212
In straight flight, as speed is reduced, whilst trimming to keep the stick force zero:
Câu 213
In a steady, horizontal, co-ordinated turn:
Câu 214
Which three aerodynamic means decrease manoeuvring stick forces?
Câu 215
Regarding deep stall characteristics, identify whether the following statements are correct or incorrect: 1) The combination of a wing with sweepback and a T-tail make an aeroplane prone to deep stall. 2) A stick pusher system can be fined to an aeroplane that exhibits abnormal stall characteristics.
Câu 216
Wing flutter can be prevented by:
Câu 217
The lift coefficient (CL) of an aeroplane in steady horizontal flight is 0.4. Increase of
angle of attack of 1° will increase CL by 0.09. A vertical up-gust instantly changes the angle of attack by 5°. The load factor will be:
Câu 218
Which statement is correct? 1) A propeller with a small blade angle is referred to as being in fine pitch. 2) A propeller with significant blade twist is referred to as being in coarse pitch.
Câu 219
Geometric washout (wing twist) means that:
Câu 220
The interference drag is the result of:
Câu 221
The lift coefficient CL versus angle of attack curve of a symmetrical aerofoil section
Intersects the horizontal axis of the graph:
Câu 222
Regarding a symmetrical aerofoil section, which statement is correct? 1) The angle of attack has a negative value when the lift coefficient equals zero. 2) A nose up pitching moment exists when the lift coefficient equals zero.
Câu 223
The dynamic pressure is equal to: (note: p = density, v = speed)
Câu 224
The additional increase of drag at Mach numbers above the critical Mach number is due to:
Câu 225
In a convergent tube with an incompressible sub-sonic airflow. the following pressure changes will occur: Ps = static pressure; PDYN = dynamic pressure; PTOT = total pressure
Câu 226
An accumulation of frost on an aircraft's wing will result in:
Câu 227
An aeroplane's sideslip angle is defined as the angle between the:
Câu 228
Regarding a positively cambered aerofoil section, which statement is correct? 1) The angle of attack has a negative value when the lift coefficient equals zero. 2) A nose down pitching moment exists when the lift coefficient equals zero.
Câu 229
The unit of measurement of pressure is:
Câu 230
Which statement about an aeroplane entering ground effect is correct? 1) The downwash angle remains constant. 2) The induced angle of attack increases.
Câu 231
Considering subsonic incompressible airflow through a Venturi, which statement is
correct? 1) The static pressure in the throat is the same as in the undisturbed airflow. 2) The speed of the airflow in the throat is higher than in the undisturbed airflow.
Câu 232
Given a constant load factor, which of these statements about the variation of induced drag with changes of speed and mass are correct or incorrect? 1) When speed decreases, induced drag decreases. 2) When mass decreases. induced drag decreases.
Câu 233
When flaps are extended whilst maintaining straight and level flight at constant lAS, the lift coefficient will:
Câu 234
Which of these statements about the gust load factor on an aeroplane are correct or
incorrect? 1) When the slope of the lift versus angle of attack curve increases, the gust load factor increases. 2) When the wing loading increases, the gust load factor decreases.
Câu 235
On an aircraft with a differential aileron control system, when the control wheel is turned to the right:
Câu 236
Which statement is correct? 1) A propeller with a small blade angle is referred to as being in coarse pitch. 2) A propeller with a large blade angle is referred to as being in fine pitch.
Câu 237
The primary purpose of equipping the power assisted flying control systems with trim capability is to:
Câu 238
An aeroplane maintains straight and level flight while the speed is doubled. The change in lift coefficient will be:
x 0.25
x 2.0
x 0.5
x 4.0
Câu 239
In straight and level flight at a speed of 1.8 Vs, the lift coefficient, expressed as a percentage of its maximum (CLMAX), would be:
324%
31%
180%
56%
Câu 240
If the straight and level stall speed is 100 kts, what will be the stall speed in a 1.3 g turn?
114 kts
130 kts
81 kts
100 kts
Câu 241
Given an initial condition in straight and level flight with a speed of 1.4 Vs. The maximum bank angle attainable without stalling in a steady co-ordinated turn, whilst maintaining speed and altitude, is approximately:
32°
44°
60°
30°
Câu 242
Stalling speed in a 15° bank level turn is 60 kts. The stalling speed in a 45° bank level turn will be:
60 kts
85 kts
70 kts
83 kts
Câu 243
The frontal area of a body, placed in a certain airstream is increased by a factor 3. If the shape does not alter, the form drag will increase by a factor of:
1.5
9
6
3
Câu 244
The Mach number is 0.8 and the TAS is 400 kts. What is the speed of sound?
480 kts
320 kts
500 kts
600 kts
Câu 245
The value of the manoeuvre stability of an aeroplane is 150 N/g. The stick force required to achieve a load factor of 25 from steady level trimmed flight is:
150 N
375 N
450 N
225 N
Câu 246
If a stick force of 20 lbs is required to pull 4g from the position of trim, the stick force gradient is:
6.6 lbs/g
5 lbs/g
20 lbs/g
60 lbs/g
Câu 247
An aeroplane flying at 200 kts in straight and level flight is subjected to a disturbance that suddenly increases the speed by 60 kts. Assuming the angle of attack remains constant, the load factor will initially:
increase to 1.3.
increase to 1.6.
increase to 1.69.
remain unchanged since the angle of attack does not change.
Câu 248
If an aeroplane performs a steady co-ordinated horizontal turn at a TAS of 200 kts and a turn radius of 2000 m, the load factor (n) will be approximately:
2.0
1.4
1.1
1.8
Câu 249
By what percentage does the lift increase in a steady level turn at 45° angle of bank, compared to straight and level flight?
41%
19%
31%
52%
Câu 250
"Given: Aeroplane mass: 50000 kg, Lift/Drag ratio: 12, Thrust per engine: 30000 N. Assumed g: 10 m/s². For a straight, steady, wings level climb of a three-engine aeroplane, the all engines climb gradient will be:"
2.9%
9.7%
8.0%
8.5%
Câu 251
What is the heading change after 10 seconds of an aeroplane performing a rate one turn?
90°
30°
180°
10°
Câu 252
"Given: Aeroplane mass: 50 000 kg, Lift/Drag ratio: 10, Thrust per engine: 20 000 N.Assumed g: 10m/s². For a straight, steady, wings level climb of a four-engine aeroplane, the all engines climb gradient will be:"
8.5%
4.3%
7.7%
6.0%
Câu 253
"Given: Aeroplane mass: 50 000 kg, Lift/Drag ratio: 12, Thrust per engine: 28 000 N. Assumed g: 10 m/s². For a straight, steady, wings level climb of a three-engine aeroplane, the all-engines climb gradient is:"
9.7%
8.0%
8.5%
2.9%
Câu 254
"Given: Aeroplane mass: 50 000 kg, Lift/Drag ratio: 12, Thrust per engine: 60 000 N. Assumed g: 10 m/s². For a straight, steady, wings level climb of a twin engine aeroplane, the one-engine-inoperative climb gradient will be:"
3.7%
15.7%
14%
11 .7%
Câu 255
At a true airspeed of 300 kts and in a 45° bank level turn, the radius of turn would be (assume a value of 1 0 m/sec² for g):
2381 m
4743 m
3354 m
23780 m
Câu 256
What is the approximate value of the lift of an aeroplane at a gross weight of 50 000 N, in a horizontal coordinated 45° banked turn?
50 000 N
60 000 N
70 000 N
80 000 N
Câu 257
With a L/D ratio of 9:1 and flying at 12000 ft the glide range in still air would be approximately:
15 NM
20 NM
14 NM
18 NM
Câu 258
"Given: Aeroplane mass: 50 000 kg, Lift/Drag ratio: 12, Thrust per engine: 50 000 N. Assumed g: 10 m/s². For a straight, steady, wings level climb of a twin engine aeroplane, the all engines climb gradient will be:"
15.7%
3.7%
14%
11.7%
Câu 259
"Given: Aeroplane mass: 50 000 kg, lift/Drag ratio: 12, Thrust per engine: 28 000 N. Assumed g: 10 m/s². For a straight, steady, wings level climb of a four-engine aeroplane. the one-engine-inoperative climb gradient will be:"
8.5%
8.0%
9.7%
2.9%
Câu 260
By what percentage does the lift increase in a steady level turn at 30° angle of bank, compared to straight and level flight?
41%
15%
50%
10%
Câu 261
All gust lines in the gust load diagram originate from a point where the:
Câu 262
An aeroplane flying at 200 kts in straight and level flight is subjected to a disturbance that suddenly increases the speed by 40 kts. Assuming the angle of attack remains constant, the load factor will initially:
Câu 263
Which of the following phenomena is counteracted by the use of differential ailerons?
Adverse yaw.
Turn co-ordination.
Sensitivity to spiral dive.
Aileron reversal.
Câu 264
Which kind of tab is commonly used in case of manual reversion of fully powered flight controls?
Balance tab.
Spring tab.
Servo tab.
Anti-balance tab.
Câu 265
Approximately how long does it take to fly a complete circle during a horizontal steady coordinated turn with a bank angle of 45° and a TAS of 200 kts?
65 seconds
95 seconds
125 seconds
650 seconds
Câu 266
An aircraft is in straight, level flight has a CL of 0.42, and a 1° increase in angle of attack would increase the CL by 0.1 . Following a gust that increases the angle of attack by 3°, what load factor would the aircraft be subject to?
0.7
1.7
1.4
2.4
Câu 267
What is the percentage increase in lift if the angle of attack increased by 4o due to a vertical gust. The straight and level coefficient of lift is 0.52, and for each 10 change in angle of attack the coefficient of lift changes by 0.07.
Câu 268
An aeroplane is in a steady horizontal turn at a TAS of 194 kts. The turn radius is 1 000 m. The bank angle is (assume g = 10 m/s²)?
45°
30°
50°
60°
Câu 269
The manoeuvre stability of a large jet transport aeroplane is 280 N/g. What stick force is required, if the aeroplane is pulled to the limit manoeuvring load factor from a trimmed horizontal straight and steady flight (cruise configuration)?
1050 N
770N
630N
420N
Câu 270
An aeroplane has a stalling speed of 100 kts in a steady level flight. When the aeroplane is flying a level turn with a load factor of 1.5 the stalling speed is:
141 kts
122 kts
82 kts
150 kts
Câu 271
Whilst maintaining straight and level flight with a lift coefficient CL = 1 what will be the new approximate value of CL after the speed is increased by 30%?
0.30
0.25
0.60
0.50
Câu 272
An aeroplane has a stall speed of 78 kts at its mass of 6850 kg. What is the stall speed when the mass is 5000 kg?
91 kts
78 kts
57 kts
67 kts
Câu 273
An aircraft maintains a 50° bank angle during a constant altitude turn. Compared to straight and level flight the stall speed will be greater by a factor of:
1.6
1.41
1.25
2.0
Câu 274
Which of these statements about the gust load factor on an aeroplane are correct or incorrect? 1) When the mass decreases, the gust load factor decreases. 2) When the altitude decreases, the gust load factor decreases.
Câu 275
What is the approximate diameter of a steady, level, co-ordinated turn with a bank angle of 30° and a speed (TAS) of 500 kts?
13 km
17 km
23 km
7 km
Câu 276
If the airspeed is increased from 90 kts to 135 kts during a level 45° banked turn. the load factor will:
decrease and the stall speed will increase.
remain the same but the radius of turn will increase.
increase as well as the stall speed.
increase and the radius of turn will increase.
Câu 277
A light twin is in a turn at 30° bank and 180 kts TAS. A heavier aeroplane at the same bank and the same speed will:
Câu 278
"Which of these statements about VMCG determination are correct or incorrect? 1) During VMCG determination, nose wheel steering may be used. 2) During VMCG determination, the CG should be on the aft limit.”
Câu 279
"Which of the following statements is correct? 1) VMCL is the minimum control speed in the landing configuration. 2) The speed VMCL is always limited by maximum rudder deflection."
Câu 280
An aeroplane climbs to cruising level with a constant pitch attitude and maximum climb thrust (assume no supercharger). How do the following variables change during the climb? (gamma = flight path angle)
gamma decreases, angle of attack increases, lAS remains constant.
gamma decreases, angle of attack increases, lAS decreases.
gamma decreases, angle of attack remains constant, lAS decreases.
gamma remains constant, angle of attack remains constant, lAS decreases.
Câu 281
In a co-ordinated horizontal turn, the magnitude of the centripetal force at 45° of bank:
is equal to the lift of the aeroplane.
Câu 282
What effect, if any, does altitude have on VMC for an aeroplane with unsupercharged engines?
Remains constant to full throttle height and then decreases.
Increases with increasing altitude.
Altitude has no effect.
Decreases with increasing altitude.
Câu 283
"Which of these statements about the limiting value of 5° bank angle dunng VMCA determination are correct or incorrect? 1) When the bank angle is decreased from 5° to 0°, the value of VMCA will remain approximately constant. 2) When the bank angle is increased beyond 5°, there is a increasing risk of fin stall."
Câu 284
1. An aeroplane in straight and level flight at 100 kts is subjected to a sudden disturbance in speed. Assuming the angle of attack remains constant initially and the load factor reaches a value of 1.96:
Câu 285
Which of the following is a correct design gust value factor applied in certification under EASA CS-25?
Câu 286
Which of the following is a correct design gust value factor applied in certification under EASA CS-25?
Câu 287
What is the limit load factor of a large transport aeroplane?
Câu 288
An aircraft is flown at 20% below its normal mass. Because of this, VA will be:
Câu 289
An aeroplane flying at 200 kts in straight and level flight is subjected to a disturbance that suddenly increases the speed by 10 kts. Assuming the angle of attack remains constant, how will the load factor be?
Câu 290
The stick force per g of a normal category aeroplane is 300 N/g. What stick force is required, if the aeroplane is pulled to the limit manoeuvring load factor from a trimmed horizontal straight and steady flight?
Câu 291
An aeroplane is flying straight and level with a coefficient of lift of 0.55. The coefficient of lift increase by 0.08 per degree increase in angle of attack. If a vertical gust increases the angle of attack by 3o, what is the increase in load factor?
Câu 292
Taper ratio is the ratio of:
the root thickness to the root chord.
the span to the root chord.
the tip chord to the root chord.
the span to the mean chord.
Câu 293
Regarding the lift formula, if density doubles, lift will:
also double.
remain the same.
be 4 times greater.
halve.
Câu 294
Which line in the diagram represents an aeroplane with static longitudinal instability at all angles of attack?
Câu 295
Which of these statements about the pitching moment coefficient versus angle of attack lines in the annex is correct?
Câu 296
The Correct sequence of cross-sections representing propeller blade twist is:
Câu 297
Which of these statements about the pitching moment coefficient versus angle of attack lines in the annex is correct?
Câu 298
Assuming all bodies have the same cross-sectional area and are in motion, which body will have the highest pressure drag?
Câu 299
Where on the curve in the diagram does the aeroplane exhibit static longitudinal
instability?
Câu 300
What kind of horizontal control surface is shown in the figure?
Câu 301
Which type of flap is shown in the picture 4?
Câu 302
Which type of flap is shown in the picture 3?
Câu 303
An aeroplane performs a straight and level horizontal flight at the same angle of attack at two different altitudes. (all other factors of importance being constant, assume ISA conditions and no compressibility effects)
Câu 304
Compared with level flight prior to the stall, the lift (1) and drag (2) in the stall change as follows:
Câu 305
A boundary layer fence on a swept wing will:
Câu 306
The formula for the Mach Number is:
(a= speed of sound)
Câu 307
When the Mach number is slowly increased in straight and level flight the first shockwaves will occur:
Câu 308
In what flight phase are the outboard ailerons (if present) not operated ?
Câu 309
Given an aeroplane in steady, straight and level flight at low speed and considering the effects of CG location and thrust, the lowest value of wing lift occurs at:
Câu 310
"Flutter" may be caused by a:
Câu 311
An aeroplane accelerates from 80 kts to 160 kts at a load factor equal to 1. By what factors will the induced drag coefficient (i) and the induced drag (ii) change?
Câu 312
What is the effect of winglets on the drag of the wing?
Câu 313
The vane of a stall warning system with a flapper switch is activated by the change of the:
Câu 314
Which of the following wing planforms produces the lowest induced drag? (assume zero wing twist)
Câu 315
Which of the following provides a positive contribution to static directional stability?
Câu 316
Spoilers mounted on the wing upper surface can be used to:
Câu 317
The positive manoeuvring limit load factor for a large jet transport aeroplane with flaps extended is:
Câu 318
If the RPM lever of a constant speed propeller is moved forward during a glide with idle power and whilst maintaining constant airspeed, the propeller pitch will:
Câu 319
The greatest drag produced by the variable pitch propeller on a piston engine will occur when the propeller is:
Câu 320
Which statement is correct?
Câu 321
A propeller with a small blade angle is referred to as being in coarse pitch.
Câu 322
A propeller with a large blade angle is referred to as being in fine pitch.
Câu 323
If the chord of the propeller blades is increased, with everything else remaining constant:
Câu 324
Given an aeroplane with a propeller turning clockwise as seen from behind, the torque effect during the take-off run will tend to:
Câu 325
The phugoid motion is a long term oscillation around the:
Câu 326
Vortex generators mounted on the upper wing surface will:
Câu 327
If pressure is kept constant and temperature increases, the density:
Câu 328
Consider an aerofoil with a certain camber and a positive angle of attack. At which location will the highest flow velocities occur?
Câu 329
Ignoring downwash effects on the tailplane, extension of Fowler-type flaps, will produce:
Câu 330
Considering subsonic incompressible airflow through a Venturi, which statement is correct?
Câu 331
The dynamic pressure in the throat is the same as in the undisturbed airflow.
Câu 332
The total pressure in the throat is lower than in the undisturbed airflow.
Câu 333
Decreasing the aspect ratio of a wing:
Câu 334
Drag is acting in the direction of ___. Lift is perpendicular to the ___.
Câu 335
On a symmetrical aerofoil, the pitching moment for which CL = 0 is:
Câu 336
If the continuity equation is applicable, what will happen to the air density (rho) if the cross sectional area of a tube changes? (low speed, subsonic and incompressible flow)
Câu 337
Which of the following wing planforms produces the lowest induced drag? (all other relevant factors constant)
Câu 338
If an aeroplane flies in the ground effect
Câu 339
The pitch up effect of an aeroplane with swept wing in a stall is due to the
Câu 340
During the take-off roll with a strong crosswind from the left, a four engine jet aeroplane with wing mounted engines experiences an engine failure above V1. Which engine causes the greatest control problem?
Câu 341
Differential aileron deflection:
Câu 342
How can wing flutter be prevented?
Câu 343
The positive manoeuvring limit load factor for a light aeroplane in the utility category in the clean configuration is:
Câu 344
Constant-speed propellers provide a better performance than fixed-pitch propellers because they:
Câu 345
If you push forward the RPM lever of a constant speed propeller during a glide with idle power and constant speed, the propeller pitch will:
Câu 346
An aeroplane performs a continuous descent with 160 KT IAS and 1000 fpm vertical speed. In this condition:
Câu 347
What factors determine the distance travelled over the ground of an aeroplane in a glide ?
Câu 348
The lift to drag ratio determines the
Câu 349
An aeroplane, being manually flown in the speed unstable region, experiences a disturbance that causes a speed reduction. If the altitude is maintained and thrust remains constant, the aeroplane speed will:
Câu 350
What is the correct relationship between the true airspeed for (i) minimum sink rate and (ii) minimum glide angle, at a given altitude?
Câu 351
The lift coefficient Cl versus angle of attack curve of a positively cambered aerofoil section intersects the horizontal axis of the graph:
Câu 352
Static pressure acts:
Câu 353
What is the effect of high aspect ratio of an aeroplane's wing on induced drag?
Câu 354
Dangerous stall characteristics, in large transport aeroplanes that require stick pushers to be installed, include:
Câu 355
The stall speed increases, when: (all other factors of importance being constant)
Câu 356
Rotation around the normal axis is called:
Câu 357
A "slat" is:
Câu 358
CL varies with:
Câu 359
If the trailing edge flaps are lowered (fully extended), in order to maintain constant IAS and level flight:
Câu 360
Which statement is correct?
I. Propeller gyroscopic effect occurs during aeroplane yaw changes.
II. Propeller gyroscopic effect is most noticeable during low speed flight at high propeller RPM.
Câu 361
Which statement is correct?
I. Stall speeds are determined with the CG at the aft limit.
II. Minimum control speeds are determined with the CG at the forward limit.
Câu 362
Which statement is correct at the speed for minimum drag (subsonic) ?
Câu 363
The effects of very heavy rain (tropical rain) on the aerodynamic characteristics of an aeroplane are:
Câu 364
In a stationary subsonic streamline flow pattern, if the streamlines converge, in this part of the pattern, the static pressure (I) will ...and the velocity (II) will ...:
Câu 365
The true airspeed (TAS) is:
Câu 366
What is the SI unit of measurement for power?
Câu 367
On an asymmetrical, single curve aerofoil, in subsonic airflow, at low angle of attack, when the angle of attack is increased, the centre of pressure will (assume a conventional transport aeroplane):
Câu 368
The frontal area of a body, placed in a certain airstream is increased by a factor 3. The shape will not alter. The aerodynamic drag will increase with a factor:
Câu 369
Which of the following will reduce induced drag?
Câu 370
Which of the following aeroplane parts affect induced drag most?
Câu 371
After take-off the slats (when installed) are always retracted later than the flaps. Why?
Câu 372
The speed of sound is affected by the:
Câu 373
What data may be obtained from the Buffet Onset Boundary chart?
Câu 374
Which of the following flight phenomena can occur at Mach numbers below the critical Mach number?
Câu 375
The critical Mach number for an aerofoil equals the free stream airfoil Mach number at which:
Câu 376
When air has passed through a shock wave the local speed of sound is:
Câu 377
To increase the critical Mach number a conventional aerofoil should
Câu 378
Which statement is correct regarding a shockwave on a lift generating wing?
Câu 379
How will the density and static temperature change in a supersonic flow from a position in front of a shock wave to behind it ?
Câu 380
During landing of a low-winged jet aeroplane, the greatest elevator up deflection is normally required when the flaps are:
Câu 381
The 'short period mode' is an:
Câu 382
The aerodynamic contribution to the static longitudinal stability of the nacelles of aft fuselage mounted engines is:
Câu 383
The effect of a ventral fin on the static stability of an aeroplane is as follows:
(1=longitudinal, 2=lateral, 3=directional)
Câu 384
Static lateral stability should not be too small, because:
Câu 385
Examples of aerodynamic balancing of control surfaces are:
Câu 386
What should be usually done to perform a landing with the stabilizer jammed in the cruise flight position ?
Câu 387
Increase of the delta load factor due to a given vertical upgust at a given EAS occurs when:
Câu 388
Does the pitch angle of a constant speed propeller alter in medium horizontal turbulence?
Câu 389
The effect of a positive wing sweep on static directional stability is as follows:
Câu 390
The gust load factor due to a vertical upgust increases when:
Câu 391
The SI units of air density (I) and force (II) are:
Câu 392
The angle between the aeroplane longitudinal axis and the chord line is the:
Câu 393
The lift force, acting on an aerofoil:
Câu 394
The continuity equation states: If the area of a tube is increasing, the speed of the subsonic and incompressible flow inside is
Câu 395
With increasing angle of attack, the stagnation point will move (I) ...and the point of lowest pressure will move (II) ...Respectively (I) and (II) are:
Câu 396
Increasing dynamic pressure will have the following effect on the drag of an aeroplane (all other factors of importance remaining constant):
Câu 397
Induced drag is created by the:
Câu 398
In what way do (1) induced drag and (2) parasite drag alter with increasing speed in straight and level flight?
Câu 399
Ground effect has the following influence on the landing distance:
Câu 400
Entering the stall the centre of pressure of a straight (1) wing and of a strongly swept back wing (2) will:
Câu 401
Increase of wing loading will:
Câu 402
The stalling speed in IAS will change according to the following factors:
Câu 403
Which of the following statements about the difference between Krueger flaps and slats is correct?
Câu 404
Mcrit is the free stream Mach Number at which:
Câu 405
At higher altitudes, the stall speed (IAS):
Câu 406
The loss of total pressure in a shock wave is due to the fact that
Câu 407
The critical Mach number can be increased by
Câu 408
Vortex generators on the upper side of the wing surface will:
Câu 409
The bow wave will first appear at:
Câu 410
In which situation would the wing lift of an aeroplane in straight and level flight have the highest value?
Câu 411
The CG of an aeroplane is in a fixed position forward of the neutral point. Which of these statements about the stick force stability is correct?
Câu 412
In case the Mach trimmer fails:
Câu 413
Which statement is correct?
Câu 414
Dihedral of the wing:
Câu 415
Given two identical aeroplanes with wing mounted engines, one fitted with jet engines and the other with counter rotating propellers, what happens following an engine failure?
Câu 416
When are outboard ailerons (if present) de-activated?
Câu 417
In general transport aeroplanes with power assisted flight controls are fitted with an adjustable stabilizer instead of trim tabs on the elevator. This is because:
Câu 418
VLE is defined as the:
Câu 419
Which statement is correct about the gust load on an aeroplane (IAS and all other factors of importance remaining constant)?
Câu 420
the gust load increases, when the weight decreases.
Câu 421
the gust load increases, when the altitude increases.
Câu 422
The torque effect during the take off run in respect of a right hand propeller, when viewed from behind, will tend to:
Câu 423
An aircraft has a buffet margin of 0.13g. 9.81m/s² standard for gravity. The maximum angle of bank where the stall is reached:
Câu 424
The relative thickness of an aerofoil is expressed as:
Câu 425
The induced drag:
Câu 426
An aeroplane transitions from steady straight and level flight into a horizontal co-ordinated turn with a load factor of 2, the speed remains constant and the:
Câu 427
In a steady level, co-ordinated turn, the load factor n and the stalling speed VS will be:
Câu 428
Which aeroplane design has the highest probability of a super stall?
Câu 429
The stalling speed in IAS will change according to the following factors:
Câu 430
When 'spoilers' are used as speed brakes:
Câu 431
An aeroplane is descending at a constant Mach number from FL 350. What is the effect on true airspeed ?
Câu 432
A jet aeroplane is cruising at high altitude with a Mach-number, that provides a buffet margin of 0.3 g incremental. In order to increase the buffet margin to 0.4 g incremental the pilot must:
Câu 433
Some aeroplanes have a 'waist' or 'coke bottle' contoured fuselage. This is done to
Câu 434
If the total sum of moments about one of its axes is not zero, an aeroplane would:
Câu 435
The (1) stick force stability and the (2) manoeuvre stability are positively affected by:
Câu 436
Positive static lateral stability is the tendency of an aeroplane to:
Câu 437
What will increase the sensitivity to Dutch Roll?
Câu 438
The manoeuvring speed VA expressed in indicated airspeed, of a transport aeroplane:
Câu 439
The angle of attack of a fixed pitch propeller blade increases when:
Câu 440
Gyroscopic precession of a propeller is induced by:
Câu 441
Which of the following statements is correct
I. VMCL is the minimum control speed in the landing configuration.
II. The speed VMCL is always limited by maximum rudder deflection.
Câu 442
Which of the following statements is correct?
I. A dorsal fin increases the contribution of the vertical tail plane to the static directional stability, in particular at large angles of sideslip.
Câu 443
The location of the centre of pressure of a positive cambered wing at increasing angle of attack will:
Câu 444
Which statement about induced drag and tip vortices is correct?
Câu 445
The induced drag coefficient, CDi is proportional to:
Câu 446
Which of the following statements about the spin is correct?
Câu 447
A jet aeroplane cruises buffet free at high constant altitude. Which type of stall can occur if this aeroplane decelerates during an inadvertent increase in load factor?
Câu 448
Deploying a Fowler flap, the flap will:
Câu 449
The trailing edge flaps when extended:
Câu 450
A plain flap will increase CLmax by
Câu 451
Spoiler deflection causes:
Câu 452
The critical Mach Number of an aeroplane is the free stream Mach Number, which produces the first evidence of:
Câu 453
Critical Mach number is the free stream Mach number at which:
Câu 454
Compared with an oblique shock wave at the same Mach number a normal shock wave has a
Câu 455
The application of the area rule on aeroplane design will decrease the
Câu 456
Which part of an aeroplane provides the greatest positive contribution to the static longitudinal stability ?
Câu 457
An aeroplane has a servo tab controlled elevator. What will happen if the elevator jams during flight?
Câu 458
What is the position of the elevator in relation to the trimmable horizontal stabiliser of a power assisted aeroplane that is in trim?
Câu 459
By what percentage does VA (EAS) alter when the aeroplane's weight decreases by 19%?
Câu 460
Which statement is correct about the gust load on an aeroplane, while all other factors of importance remain constant?
I When the mass increases, the gust load increases.
II When the altitude decreases, the gust load increases.
Câu 461
If you decrease the propeller pitch during a glide with idle-power at constant IAS the lift to drag ratio will:
Câu 462
Which statement, about an aeroplane entering ground effect at constant angle of attack, is correct?
Câu 463
The lift coefficient CL increases.
Câu 464
The induced drag coefficient CDi increases.
Câu 465
The mean camber line of an aerofoil section is:
Câu 466
The span-wise flow is caused by the difference between the air pressure on top and beneath the wing and its direction of movement goes from:
Câu 467
Which of the following wing planforms gives the highest local lift coefficient at the wing root?
Câu 468
During an erect spin recovery:
Câu 469
Which type of stall has the largest associated angle of attack?
Câu 470
After the transition point between the laminar and turbulent boundary layer
Câu 471
The wing of an aeroplane will never stall at low subsonic speeds as long as....
Câu 472
One important advantage the turbulent boundary layer has over the laminar layer is that:
Câu 473
Assuming ISA conditions, which statement with respect to the climb is correct ?
Câu 474
The critical Mach Number of an aeroplane can be increased by:
Câu 475
The Mach-trim function is installed on most commercial jets in order to minimize the adverse effects of:
Câu 476
Tuck under will happen
Câu 477
On a un-swept wing, when the aerofoil is accelerated from subsonic to supersonic speeds, the aerodynamic centre:
Câu 478
Which statement is correct for a side slip condition at constant speed and side slip angle, where the geometric dihedral of an aeroplane is increased ?
Câu 479
If the nose of an aeroplane yaws left, this causes:
Câu 480
Which of the following statements is true?
Câu 481
If you increase the propeller pitch during a glide with idle-power at constant IAS the lift to drag ratio will
Câu 482
The difference between IAS and TAS will:
Câu 483
Bernoulli's law states:
(note: rho is the mean sea level density under ISA conditions; pstat is static pressure; pdyn is dynamic pressure; ptot is total pressure)
Câu 484
The aerofoil polar is:
Câu 485
Induced drag may be reduced by:
Câu 486
Which of the following statements about boundary layers is correct?
Câu 487
Which of the following statements about the stall of a straight wing aeroplane is correct?
Câu 488
The most important problem of ice accretion on a transport aeroplane during flight is:
Câu 489
Vortex generators:
Câu 490
In order to maintain straight and level flight at a constant airspeed, whilst the flaps are being retracted, the angle of attack must be: